How to fit a wood burning stove in a shed

Fitting a wood burning stove in a wooden building

How to fit a wood burning or multifuel stove in a shed

 

Fitting a stove in a shed or summerhouse needn’t be complicated if a few basic rules are followed. In this article, we will demonstrate the basics and show you the products we have an offer that will make this installation as easy and most of all safe as possible. A woodburner is a fantastic addition to a shed, summerhouse or garden room and will provide a beautiful focal point. If you going to fit a stove in a summerhouse or shed then you will need a full kit of parts.

small stove in Summerhouse

Considerations before fitting a stove or Logburner in a shed or wooden building

Firstly it’s worth working out roughly what output of stove you require to heat the shed. This is simple and can be done by filling in the details below

The Stove KW calculator should only be used as a guide to verify the required stove please feel free to contact us.

The most common stoves we fit in garden rooms are The Vesta V2 Summerhouse kit and the Bushmaster Summerhouse kit

These stoves are ideal as they work on a very short flue system ie over 2 meters. Wed sells a full kit of parts so you will have everything you need delivered in one package with simple instructions that will guide you through the process. You can find a case study here of an install in a summerhouse

Step 1 – Siting the stove in the shed

Choosing the best position for your stove is quite simple. The flue system is always better to go straight up with no bends at all. Placing the floor plate in position and using a string line to estimate the flue centre position is a really helpful way to assess where the chimney will pass through the roof. It will also show you if you have any supporting structures in the way of the flue penetration and you can then re-position the stove accordingly. Ensure that you have at least 500mm of combustible materials on either side of the stove for safety.

Positioning the stove in a shed]

Step 2 – Fit the heat shield

The heat shield is required to keep the heat of the stove from damaging the back wall of the shed. We supply this with the stove kit. It simply lines up with the hearth plate (see image) and screws to the wall using the spacers supplied.  The heat shield is comprised of heat-resistant board materials with a steel cladding face that is colour-matched to your stove. Once the positions now determined. Use the plumb line again to make a mark on the ceiling that lines up with the hole in the top of the stove.

Step 2 – Cutting a flue hole in the shed roof

Now it’s time for the fun bit. Yes, it can be a bit scary cutting a hole in the roof of your brand-new shed or garden room but don’t panic we have made it easy by supplying templates and cover plates. Place the template central to the mark you just made for the centre of the flue and use the template to mark the elliptical hole.  Pilot drill the hole with a spade bit and use a jigsaw or reciprocating saw to cut all the way through the roof materials. The template has been made to give you the correct clearances required around the flue system

Cutting hole in shed roof

.

Step 3 – Assemble the Shed Stove and flue system

Ok now you have a gaping hole in your lovely shed roof it’s time to think about sorting that out before the family comes home! Start by placing the first single wall flue in the stove. The junction of the two types of flue should be approximately 300mm below the roof. Measure and cut the second section of single wall flue to achieve this using a slitting disc and an angle grinder. remove the flue from the stove pack fire cement in the hole to create a seal and push the flue back in. You can then assemble the remaining flue and poke it through the roof.

Step 4 – Roof Flashing Installation

Stove flue installed in shed

There are several methods that you can use based on the material your roof is made out of. Our rubber flashing supplied with the summerhouse stove kit is extremely durable and lasts a lifetime.

Once the flashing is fitted you can go ahead and cover it up with the storm collar and fit the cowl to the flue. It’s worth mentioning at this point that you can start to take credit for your hard work!

I am not going to go into the in-depth details of how to fit a flashing and make it watertight due to the nature of the individual room materials But a quick search on youtube will give you some pointers until I create a video tutorial!

Stove installed in log cabin

Step 4 – Tidying up

In our Summerhouse stove kit, you will have found two small plates. These are very very very important!! Basically, they cover up the mistake you made when cutting the flue hole and provide a nice finish to the ceiling. Ok, get cutting firewood because you have just finished installing a stove in your shed. Oh! Don’t forget to cut the kindling ready to start the fire

Step 5 – STOP!! One last thing

Our stove kits come with a carbon monoxide detector. Please install in straight away! The chance of getting carbon monoxide poisoning is very small but why risk it when we have the technology. 

Win a garden room Stove kit.

We are currently running a competition on our facenbook page to win a full Vesta V2 Summerhouse Kit.

Click see more below to enter.


Bank Holiday Sale Now On

Whilst Stock Last

Tel 01704 821095

The Fiesta Garden Stove is now in Stock

10%OFF

Easter Bank Holiday discount code now active. Fill in the form to get the code sent direct to your inbox

 

Get In Touch

For our fastest response please use the contact form below.

Our response is normally within a 15 minutes during office hours

Contact Information

01704 821095
sales@vestastoves.co.uk

Opening Hours

Monday – Friday 9am-1pm 
Weekend – Closed

Address

Sevenoaks, 197 Hesketh Lane. Tarleton. PR4 6AT